mirror of https://github.com/OpenIPC/wiki.git
213 lines
6.8 KiB
Markdown
213 lines
6.8 KiB
Markdown
# OpenIPC Wiki
|
|
[Table of Content](../README.md)
|
|
|
|
RunCam WiFiLink based on OpenIPC
|
|
--------------------------------
|
|
|
|
### Q&A with RunCam Dev
|
|
|
|
- What changes have you made compared to the original OpenIPC firmware ?
|
|
- We optimized the IQ sensor and added the /etc/user_config.sh script to implement the WiFi card configuration function.
|
|
|
|
Runcam Setup
|
|
--------------------------------
|
|
|
|
So you just bought a Runcam WiFi link? Great! This guide will help you to set it up.
|
|
The Runcam WiFi link and OpenIPC is still under development, so it's
|
|
possible this guide will soon be outdated.
|
|
|
|
Issue date: 01 October 2024
|
|
|
|
## What you will need:
|
|
|
|
- INAV 7.1.2
|
|
|
|
- Flight Controller: In this example, Speedybee f405 WING APP was used.
|
|
- Runcam WiFiLink + Android Ground station
|
|
- A working PC/laptop computer with an ethernet port
|
|
- USB C cable
|
|
- A fairly modern Smartphone with Android 13 or 14 installed. The smartphone should have a good processor ie. Snapdragon
|
|
- Internet connection
|
|
|
|
## 1. Hardware Setup
|
|
|
|
a) Connect the antennas to Runcam.
|
|
|
|
b) Connect the 4 cable to UART on Spedybee dedicated to connecting
|
|
digital VTX's use the image below as a guide.\
|
|
**Attention:** the cable color codes will match only on one end.
|
|
Double check your wiring (gnd to gnd, vcc to vcc, etc)
|
|
|
|
c) Insert a formatted micro SD card into the Runcam. The slot is on the
|
|
bottom of the unit, when the fan faces up.
|
|
|
|
d) Connect an Ethernet cable supplied with Runcam to the device.
|
|
|
|
## 2. INAV Setup.
|
|
|
|
a) Connect your flight controller through a USB C to a computer that
|
|
> has INAV configurator installed
|
|
|
|
b) In the Ports tab, set up MSP Display port as per image below.
|
|
Note:
|
|
if you are using a different FC then in this example, you might
|
|
need to chose a different
|
|
UART.
|
|
|
|
|
|
c) In the configuration tab, make sure Telemetry and OSD are enabled
|
|
|
|
|
|
|
|
Set up OSD in OSD tab. Enable and arrange all the information as
|
|
you wish. Set Video Format to AVATAR.
|
|
|
|
|
|
## 3. Runcam Setup
|
|
|
|
a) Insert an empty, formatted micro SD into the runcam device. The card
|
|
> pads need to face the board. The slot for the micro SD can be on
|
|
> the 'inside' of the board so you might need to disassemble it to
|
|
> put the card in.
|
|
|
|
b) When you first power up your runcam, the device will create a 'user'
|
|
> file and a 'gs.key' file. Take the SD card out from your runcam
|
|
> and copy the GS.key file into your android device. You can do it
|
|
> easily using ie. google drive.
|
|
|
|
## 4. OpenIPC Configurator setup
|
|
|
|
OpenIPC configurator is a useful tool to change many different settings
|
|
on your camera that runs OpenIPC firmware.
|
|
|
|
a) Download and install the latest version of
|
|
[PUTTY](https://www.chiark.greenend.org.uk/~sgtatham/putty/)
|
|
|
|
b) Download the [OpenIPC
|
|
configurator](https://github.com/OpenIPC/configurator/releases)
|
|
and install it
|
|
|
|
c) Setting up IP\
|
|
> -Connect your runcam to your computer's Ethernet port with the
|
|
> Ethernet cable provided by Runcam\
|
|
> - Open up a windows file browser, scroll down on the left bar and
|
|
> left click on Network, select properties.\
|
|
> - Select change adapter settings\
|
|
> - double click on Internet Protocol Version 4\
|
|
> - Enter numbers as per image below\
|
|
|
|
|
|
d) On the configurator, enter IP address: 192.168.1.10 and press
|
|
> connect
|
|
|
|
e) Refer to separate wiki document
|
|
for setting up OSD
|
|
|
|
f) Set up all the settings. There are too many to go through them all
|
|
here.
|
|
|
|
## 5. Android Ground station
|
|
|
|
a) Download [Pixel Pilot
|
|
Apk](https://github.com/OpenIPC/PixelPilot/releases)
|
|
file from github, straight into your phone.
|
|
|
|
b) Go into Android file browser, find that file and install it.
|
|
|
|
c) Open the Pixel Pilot app, and tap at the gear icon in top left
|
|
corner
|
|
|
|
d) Set up: Channel: 161
|
|
|
|
e) Connect the external wifi adapter with the phone through a USB to
|
|
USB C adapter. The adapter from runcam can be faulty so if your
|
|
WFB service doesn\'t start, try a different adapter. It needs to
|
|
be OTG (on the go) adapter.
|
|
|
|
f) Connect antennas to your external WiFi adapter.
|
|
|
|
g) Press the gear icon, then press GS.key, then navigate to the GS.key
|
|
file you have copied over from the sd card. Select that file.
|
|
|
|
## 6. Running the video stream
|
|
|
|
a) Turn on the App
|
|
|
|
b) Power on your aircraft. The Runcam should start by itself and the
|
|
fan should be spinning.
|
|
|
|
c) After 12-14 seconds you should see on your phone the video from your
|
|
aircraft.
|
|
|
|
## Mirroring the camera:
|
|
|
|
The default camera orientation is so that the top of the video is where
|
|
the cable is.
|
|
|
|
If you prefer the cable on the bottom, do the following steps:
|
|
|
|
1) Take the micro SD card out from your Runcam
|
|
|
|
2) Connect the micro SD card to your computer/laptop
|
|
|
|
3) Use Notepad to open the file 'User'.
|
|
|
|
4) Use the following settings:
|
|
> Mirror = True
|
|
> Flip = True
|
|
|
|
5) Save the file
|
|
|
|
6) Put the micro SD back into the camera
|
|
|
|
## Adding audio
|
|
|
|
1) Make sure you have the latest [Pixel
|
|
pilot installed](https://github.com/OpenIPC/PixelPilot/releases)
|
|
|
|
|
|
2) Install Win SCP to connect to your camera
|
|
|
|
3) Connect your camera with ethernet cable and power it on ( use a 3s
|
|
> battery or a 12V power source
|
|
|
|
4) Open WinSCP and connect to your camera
|
|
|
|
|
|
5) Go to: etc folder
|
|
|
|
6) Open majestic.yaml file with notepad
|
|
|
|
7) Scroll down and make sure 'audio' section is as below. You can just
|
|
edit it like a text file.
|
|
|
|
|
|
|
|
9) Save the file and close the winscp
|
|
|
|
10) Test if audio in pixel pilot app works.
|
|
At the time of writing this Audio works, but it's not being
|
|
recorded in the mp4 file.
|
|
|
|
## Troubleshooting:
|
|
|
|
**There is no video on my android device.**
|
|
|
|
Make sure the GS.key file was properly set up. (see point 3 c))
|
|
|
|
There is still no video
|
|
|
|
Check if the WiFi card gets hot when Runcam is on. If it's cold, that
|
|
means the WiFi broadcast isn't running.
|
|
|
|
|
|
### Links
|
|
|
|
- https://shop.runcam.com/runcam-wifilink-based-on-openipc/
|
|
- https://store-m8o52p.mybigcommerce.com/product_images/img_runcma_wifilink/runcma-wifilink-manual-en.pdf
|
|
- https://www.runcam.com/download/runcamwifilink
|
|
-
|
|
- https://runcam.world.taobao.com
|
|
- https://item.taobao.com/item.htm?id=823103143737&skuId=5704904774133
|
|
- https://fr.aliexpress.com/item/1005007532941097.html?gatewayAdapt=glo2fra
|