mirror of https://github.com/OpenIPC/wiki.git
Luis Alves
GitHub
parent
37a32f8dce
commit
b0fc19a5bd
|
|
@ -0,0 +1,377 @@
|
|||
# Chacon IPCAM-RI01
|
||||
|
||||
|
||||
|
||||
[Product datasheet](https://chacon.com/datasharing/doc/IPCAM-RI01/ipcam-ri01_user_manual.pdf)
|
||||
|
||||
This camera is a rebrand of a manufacturing company identified by "PPStrong".
|
||||
I'm sure there are other cameras out there that are using the same hardware (or similar with minor changes).
|
||||
|
||||
## Hardware
|
||||
|
||||
| System | Description |
|
||||
|--------|-------------------|
|
||||
| SoC | HI3518EV300 |
|
||||
| Sensor | JXF23 |
|
||||
| Flash | 16Mb (XM25QH128A) |
|
||||
| WiFi | RTL8188FU |
|
||||
|
||||
#### OpenIPC status
|
||||
|
||||
| Component | Status |
|
||||
|-----------|--------|
|
||||
| WiFi | [Working](https://github.com/OpenIPC/firmware/issues/48) |
|
||||
| Motors | [Working](https://github.com/OpenIPC/wiki/new/master/en#motor-driver) (patched driver) |
|
||||
| Red/Blue leds | Manual gpio control possible |
|
||||
| IR Cut | Manual gpio control possible |
|
||||
|
||||
#### Hardware details
|
||||
|
||||
The camera mainboard is identified by "SPEED5S-H1MB_F23".
|
||||
|
||||
|
||||
At the top of the mainboard:
|
||||
- a micro sdcard slot on the right
|
||||
- connector labeled "IR" powers the IR led, a red led and a blue led
|
||||
- connector "ICR" powers the IR cut filter
|
||||
- non-identified connector is an input for the microphone
|
||||
- SPI NOR flash chip (QH128A)
|
||||
|
||||
|
||||
|
||||
At the bottom of the mainboard:
|
||||
- SoC Hi3518EV300
|
||||
- WiFi module RTL8188FTV
|
||||
- Reset switch
|
||||
- Connectors (top to bottom):
|
||||
- Power (5V from a micro usb connector)
|
||||
- Tilt/vertical stepper motor
|
||||
- Pan/horizontal stepper motor
|
||||
- Speaker
|
||||
- UART pins at the lower left
|
||||
|
||||
### SoC
|
||||
[Hi35218EV300](https://www.hisilicon.com/en/products/smart-vision/consumer-camera/IOTVision/Hi3518EV300)
|
||||
- ARM Cortex-A7@ 900 MHz
|
||||
- 64Mb DDR2
|
||||
|
||||
|
||||
|
||||
|
||||
### Wifi
|
||||
[RTL8188FTV](https://www.realtek.com/en/products/communications-network-ics/item/rtl8188ftv)
|
||||
- 802.11b/g/n 2.4G
|
||||
- USB interface
|
||||
|
||||
|
||||
|
||||
|
||||
### SPI NOR flash
|
||||
[XM25QH128A](https://www.xmcwh.com/en/site/product_con/200)
|
||||
- 16Mb SPI NOR Flash
|
||||
|
||||
|
||||
|
||||
|
||||
### UART pins (serial port)
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
### GPIOs
|
||||
|
||||
| nr | Description |
|
||||
|-----|-------------|
|
||||
| 0x0f (15) | irCut_1 |
|
||||
| 0x0c (12) | irCut_2 |
|
||||
| 0x28 (40) | IR Led |
|
||||
| 0x33 (51) | Red Led |
|
||||
| 0x32 (50) | Blue Led |
|
||||
| 0x0d (13) | wlan power |
|
||||
| 0x00 (0) | AcShdn |
|
||||
| 0x09 (9) | Reset button |
|
||||
| 0x3b (59) | Tilt motor A1 |
|
||||
| 0x3a (58) | Tilt motor A2 |
|
||||
| 0x39 (57) | Tilt motor B1 |
|
||||
| 0x38 (56) | Tilt motor B2 |
|
||||
| 0x47 (71) | Pan motor A1 |
|
||||
| 0x45 (69) | Pan motor A2 |
|
||||
| 0x46 (70) | Pan motor B1 |
|
||||
| 0x44 (68) | Pan motor B2 |
|
||||
|
||||
### Mods
|
||||
#### USB Serial port
|
||||
|
||||
There is a micro usb connector to power the camera and with some soldering this connector can be also be used for a serial to usb converter.
|
||||
If you find it hard to solder the wires on the camera micro usb connector get a [micro usb breakout board](https://www.google.com/search?q=micro+usb+breakout+board&tbm=isch).
|
||||
|
||||
|
||||
|
||||
1. Get a 3.3V TTL to USB converter (using a cheap pl2303hx one)
|
||||
2. Remove the USB-A connector and pins
|
||||
3. Connect the camera micro usb port to the converter
|
||||
4. Connect the camera uart to the converter
|
||||
|
||||
|
||||
## Original firmware
|
||||
|
||||
The camera has a password protected uBoot.
|
||||
|
||||
### [ipctool](https://github.com/OpenIPC/ipctool) output:
|
||||
(soon...)
|
||||
|
||||
#### cat /proc/mtd
|
||||
```
|
||||
dev: size erasesize name
|
||||
mtd0: 00060000 00010000 "bld" 393216 0
|
||||
mtd1: 00010000 00010000 "env" 65536 393216
|
||||
mtd2: 00010000 00010000 "enc" 65536 458752
|
||||
mtd3: 00010000 00010000 "sysflg" 65536 524288
|
||||
mtd4: 00380000 00010000 "sys" 3670016 589824
|
||||
mtd5: 00680000 00010000 "app" 6815744 4259840
|
||||
mtd6: 00180000 00010000 "cfg" 1572864 11075584
|
||||
mtd7: 00100000 00010000 "recove" 1048576 12648448
|
||||
mtd8: 002d0000 00010000 "user" 2949120 13697024
|
||||
mtd9: 00020000 00010000 "oeminfo" 131072 16646144 - 16777216
|
||||
```
|
||||
|
||||
|
||||
### dmesg
|
||||
(soon...)
|
||||
|
||||
|
||||
## OpenIPC firmware
|
||||
|
||||
#### Boot dump
|
||||
```
|
||||
Uncompress Ok!
|
||||
|
||||
U-Boot 2016.11-g059901b-dirty (Oct 13 2021 - 20:14:30 +0300)hi3518ev300
|
||||
|
||||
Relocation Offset is: 0374a000
|
||||
Relocating to 43f4a000, new gd at 43f09ef0, sp at 43f09ed0
|
||||
SPI Nor: hifmc_ip_ver_check(44): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(50): Found
|
||||
hifmc_spi_nor_probe(1709): SPI Nor ID Table Version 1.0
|
||||
hifmc_spi_nor_probe(1734): SPI Nor(cs 0) ID: 0x20 0x70 0x18
|
||||
hifmc_spi_nor_probe(1799): Block:64KB hifmc_spi_nor_probe(1800): Chip:16MB hifmc_spi_nor_probe(1801): Name:"XM25QH128A"
|
||||
hifmc100_spi_nor_probe(147): SPI Nor total size: 16MB
|
||||
NAND: 0 MiB
|
||||
MMC: hisi-sdhci: 0 (SD)
|
||||
In: serial
|
||||
Out: serial
|
||||
Err: serial
|
||||
Net: eth0
|
||||
Warning: eth0 (eth0) using random MAC address - 6e:9f:f3:d7:33:35
|
||||
|
||||
Hit any key to stop autoboot: 0
|
||||
device 0 offset 0x50000, size 0x200000
|
||||
|
||||
SF: 2097152 bytes @ 0x50000 Read: OK
|
||||
## Booting kernel from Legacy Image at 42000000 ...
|
||||
Image Name: Linux-4.9.37-hi3518ev300
|
||||
Image Type: ARM Linux Kernel Image (uncompressed)
|
||||
Data Size: 1891696 Bytes = 1.8 MiB
|
||||
Load Address: 40008000
|
||||
Entry Point: 40008000
|
||||
Loading Kernel Image ... OK
|
||||
|
||||
Starting kernel ...
|
||||
|
||||
Booting Linux on physical CPU 0x0
|
||||
Linux version 4.9.37 (runner@fv-az241-255) (gcc version 7.5.0 (Buildroot -g29dde73) ) #1 Sun Jan 9 03:44:04 UTC 2022
|
||||
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
|
||||
CPU: div instructions available: patching division code
|
||||
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
|
||||
OF: fdt:Machine model: Hisilicon HI3518EV300 DEMO Board
|
||||
cmz zone is not set!
|
||||
Memory policy: Data cache writeback
|
||||
CPU: All CPU(s) started in SVC mode.
|
||||
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
|
||||
Kernel command line: mem=32M console=ttyAMA0,115200 panic=20 rootfstype=squashfs root=/dev/mtdblock3 init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel
|
||||
),5120k(rootfs),-(rootfs_data) mmz_allocator=hisi
|
||||
PID hash table entries: 128 (order: -3, 512 bytes)
|
||||
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
|
||||
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
|
||||
Memory: 27104K/32768K available (3861K kernel code, 141K rwdata, 872K rodata, 188K init, 179K bss, 5664K reserved, 0K cma-reserved)
|
||||
Virtual kernel memory layout:
|
||||
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
|
||||
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
|
||||
vmalloc : 0xc2800000 - 0xff800000 ( 976 MB)
|
||||
lowmem : 0xc0000000 - 0xc2000000 ( 32 MB)
|
||||
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
|
||||
.text : 0xc0008000 - 0xc03cd778 (3862 kB)
|
||||
.init : 0xc04a9000 - 0xc04d8000 ( 188 kB)
|
||||
.data : 0xc04d8000 - 0xc04fb520 ( 142 kB)
|
||||
.bss : 0xc04fd000 - 0xc0529fe4 ( 180 kB)
|
||||
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
|
||||
NR_IRQS:16 nr_irqs:16 16
|
||||
Gic dist init...
|
||||
arm_arch_timer: Architected cp15 timer(s) running at 50.00MHz (phys).
|
||||
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
|
||||
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
|
||||
Switching to timer-based delay loop, resolution 20ns
|
||||
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
|
||||
Console: colour dummy device 80x30
|
||||
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
|
||||
pid_max: default: 32768 minimum: 301
|
||||
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
|
||||
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
|
||||
CPU: Testing write buffer coherency: ok
|
||||
Setting up static identity map for 0x40008200 - 0x40008258
|
||||
devtmpfs: initialized
|
||||
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
|
||||
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
|
||||
futex hash table entries: 256 (order: -1, 3072 bytes)
|
||||
pinctrl core: initialized pinctrl subsystem
|
||||
NET: Registered protocol family 16
|
||||
DMA: preallocated 256 KiB pool for atomic coherent allocations
|
||||
Serial: AMBA PL011 UART driver
|
||||
12040000.uart: ttyAMA0 at MMIO 0x12040000 (irq = 21, base_baud = 0) is a PL011 rev2
|
||||
console [ttyAMA0] enabled
|
||||
12041000.uart: ttyAMA1 at MMIO 0x12041000 (irq = 22, base_baud = 0) is a PL011 rev2
|
||||
ssp-pl022 12070000.spi: ARM PL022 driver, device ID: 0x00800022
|
||||
ssp-pl022 12070000.spi: mapped registers from 0x12070000 to c286b000
|
||||
ssp-pl022 12071000.spi: ARM PL022 driver, device ID: 0x00800022
|
||||
ssp-pl022 12071000.spi: mapped registers from 0x12071000 to c286f000
|
||||
usbcore: registered new interface driver usbfs
|
||||
usbcore: registered new interface driver hub
|
||||
usbcore: registered new device driver usb
|
||||
clocksource: Switched to clocksource arch_sys_counter
|
||||
NET: Registered protocol family 2
|
||||
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
|
||||
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
|
||||
TCP: Hash tables configured (established 1024 bind 1024)
|
||||
UDP hash table entries: 256 (order: 0, 4096 bytes)
|
||||
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
|
||||
NET: Registered protocol family 1
|
||||
RPC: Registered named UNIX socket transport module.
|
||||
RPC: Registered udp transport module.
|
||||
RPC: Registered tcp transport module.
|
||||
RPC: Registered tcp NFSv4.1 backchannel transport module.
|
||||
workingset: timestamp_bits=30 max_order=13 bucket_order=0
|
||||
squashfs: version 4.0 (2009/01/31) Phillip Lougher
|
||||
jffs2: version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
|
||||
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
|
||||
io scheduler noop registered
|
||||
io scheduler deadline registered (default)
|
||||
pl061_gpio 120b0000.gpio_chip: PL061 GPIO chip @0x120b0000 registered
|
||||
pl061_gpio 120b1000.gpio_chip: PL061 GPIO chip @0x120b1000 registered
|
||||
pl061_gpio 120b2000.gpio_chip: PL061 GPIO chip @0x120b2000 registered
|
||||
pl061_gpio 120b4000.gpio_chip: PL061 GPIO chip @0x120b4000 registered
|
||||
pl061_gpio 120b5000.gpio_chip: PL061 GPIO chip @0x120b5000 registered
|
||||
pl061_gpio 120b6000.gpio_chip: PL061 GPIO chip @0x120b6000 registered
|
||||
pl061_gpio 120b7000.gpio_chip: PL061 GPIO chip @0x120b7000 registered
|
||||
pl061_gpio 120b8000.gpio_chip: PL061 GPIO chip @0x120b8000 registered
|
||||
brd: module loaded
|
||||
loop: module loaded
|
||||
hisi-sfc hisi_spi_nor.0: SPI Nor ID Table Version 1.2
|
||||
hisi-sfc hisi_spi_nor.0: The ID: 0x20 isn't in the BP table, Current device can't not protect
|
||||
@spi_nor_scan(), no "m25p,fast-read".
|
||||
@spi_nor_scan(), modes->rd_modes:0xd.
|
||||
hisi-sfc hisi_spi_nor.0: (Fast) Read: opcode=BBh, protocol=122, mode=0, wait=8
|
||||
hisi-sfc hisi_spi_nor.0: nor->read_opcode[3: Read; 0B: Fast Read; 3B: Dual; BB: Dual IO; 6B: Quad; EB: Quad IO]: 0xbb.
|
||||
hisi-sfc hisi_spi_nor.0: xm25qh128a (Chipsize 16 Mbytes, Blocksize 64KiB)
|
||||
5 cmdlinepart partitions found on MTD device hi_sfc
|
||||
5 cmdlinepart partitions found on MTD device hi_sfc
|
||||
Creating 5 MTD partitions on "hi_sfc":
|
||||
0x000000000000-0x000000040000 : "boot"
|
||||
0x000000040000-0x000000050000 : "env"
|
||||
0x000000050000-0x000000250000 : "kernel"
|
||||
0x000000250000-0x000000750000 : "rootfs"
|
||||
0x000000750000-0x000001000000 : "rootfs_data"
|
||||
SPI Nand ID Table Version 2.7
|
||||
Cannot found a valid SPI Nand Device
|
||||
hisi_spi_nand_probe(175): Error: driver probe, result: -19
|
||||
No OTP data, festa PHY use default ATE parameters!
|
||||
festa PHY wait autotrim done timeout!
|
||||
libphy: hisi_femac_mii_bus: probed
|
||||
libphy: Fixed MDIO Bus: probed
|
||||
hisi-femac 10040000.ethernet: connect to PHY failed!
|
||||
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
|
||||
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
|
||||
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6c hci version 0x110 quirks 0x20010010
|
||||
xhci-hcd xhci-hcd.0.auto: irq 116, io mem 0x10030000
|
||||
hub 1-0:1.0: USB hub found
|
||||
hub 1-0:1.0: 1 port detected
|
||||
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
|
||||
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
|
||||
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
|
||||
hub 2-0:1.0: USB hub found
|
||||
hub 2-0:1.0: hub can't support USB3.0
|
||||
hibvt_rtc 120e0000.rtc: rtc core: registered 120e0000.rtc as rtc0
|
||||
hibvt_rtc 120e0000.rtc: RTC driver for hibvt enabled
|
||||
i2c /dev entries driver
|
||||
hibvt-i2c 12060000.i2c: hibvt-i2c0@100000hz registered
|
||||
hibvt-i2c 12061000.i2c: hibvt-i2c1@100000hz registered
|
||||
hibvt-i2c 12062000.i2c: hibvt-i2c2@100000hz registered
|
||||
sdhci: Secure Digital Host Controller Interface driver
|
||||
sdhci: Copyright(c) Pierre Ossman
|
||||
sdhci-pltfm: SDHCI platform and OF driver helper
|
||||
mmc0: SDHCI controller on 10010000.sdhci [10010000.sdhci] using ADMA in legacy mode
|
||||
mmc1: SDHCI controller on 10020000.sdhci [10020000.sdhci] using ADMA in legacy mode
|
||||
NET: Registered protocol family 10
|
||||
NET: Registered protocol family 17
|
||||
hibvt_rtc 120e0000.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)
|
||||
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
|
||||
devtmpfs: mounted
|
||||
Freeing unused kernel memory: 188K (c04a9000 - c04d8000)
|
||||
This architecture does not have kernel memory protection.
|
||||
mmc0: new high speed SDHC card at address 1234
|
||||
mmcblk0: mmc0:1234 SA08G 7.21 GiB
|
||||
mmcblk0: p1
|
||||
Starting syslogd: OK
|
||||
Starting klogd: OK
|
||||
Running sysctl: OK
|
||||
Loading modules:Initializing random number generator: OK
|
||||
Saving random seed: OK
|
||||
Starting rngd: OK
|
||||
Starting mdev...
|
||||
F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock
|
||||
F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock
|
||||
F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock
|
||||
F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock
|
||||
Starting network: OK
|
||||
Starting ntpd: OK
|
||||
Starting dropbear sshd: OK
|
||||
Starting httpd: OK
|
||||
Starting mini-snmpd: DISABLED, OK
|
||||
Starting telnetd: DISABLED, OK
|
||||
Starting crond: OK
|
||||
mmz_start: 0x42000000, mmz_size: 32M
|
||||
hisilicon: Get data from environment and set SENSOR as jxf23
|
||||
insert audio
|
||||
Bringing wlan0 up...
|
||||
Successfully initialized wpa_supplicant
|
||||
rfkill: Cannot open RFKILL control device
|
||||
udhcpc: started, v1.31.1
|
||||
udhcpc: sending discover
|
||||
udhcpc: sending discover
|
||||
udhcpc: sending discover
|
||||
udhcpc: sending select for 192.168.1.112
|
||||
udhcpc: lease of 192.168.1.112 obtained, lease time 86400
|
||||
deleting routers
|
||||
adding dns 8.8.8.8
|
||||
adding dns 8.8.4.4
|
||||
hisilicon: Check MAC for Xiongmai devices
|
||||
hisilicon: The eth0 interface has a correct MAC -
|
||||
hisilicon: Loading of kernel modules and initialization of the video system has started
|
||||
Starting majestic: OK
|
||||
|
||||
Welcome to OpenIPC v2.1
|
||||
openipc-hi3518ev300 login:
|
||||
```
|
||||
|
||||
|
||||
(soon...)
|
||||
|
||||
### rtl8188fu
|
||||
(soon...)
|
||||
|
||||
### Motor driver
|
||||
(soon...)
|
||||
|
||||
|
||||
|
||||
## Flashing
|
||||
(soon...)
|
||||
Loading…
Reference in New Issue