diff --git a/en/device-chacon_ipcam-ri01.md b/en/device-chacon_ipcam-ri01.md new file mode 100644 index 0000000..a6bfbc6 --- /dev/null +++ b/en/device-chacon_ipcam-ri01.md @@ -0,0 +1,377 @@ +# Chacon IPCAM-RI01 + + + +[Product datasheet](https://chacon.com/datasharing/doc/IPCAM-RI01/ipcam-ri01_user_manual.pdf) + +This camera is a rebrand of a manufacturing company identified by "PPStrong". +I'm sure there are other cameras out there that are using the same hardware (or similar with minor changes). + +## Hardware + +| System | Description | +|--------|-------------------| +| SoC | HI3518EV300 | +| Sensor | JXF23 | +| Flash | 16Mb (XM25QH128A) | +| WiFi | RTL8188FU | + +#### OpenIPC status + +| Component | Status | +|-----------|--------| +| WiFi | [Working](https://github.com/OpenIPC/firmware/issues/48) | +| Motors | [Working](https://github.com/OpenIPC/wiki/new/master/en#motor-driver) (patched driver) | +| Red/Blue leds | Manual gpio control possible | +| IR Cut | Manual gpio control possible | + +#### Hardware details + +The camera mainboard is identified by "SPEED5S-H1MB_F23". + + +At the top of the mainboard: +- a micro sdcard slot on the right +- connector labeled "IR" powers the IR led, a red led and a blue led +- connector "ICR" powers the IR cut filter +- non-identified connector is an input for the microphone +- SPI NOR flash chip (QH128A) + + + +At the bottom of the mainboard: +- SoC Hi3518EV300 +- WiFi module RTL8188FTV +- Reset switch +- Connectors (top to bottom): + - Power (5V from a micro usb connector) + - Tilt/vertical stepper motor + - Pan/horizontal stepper motor + - Speaker +- UART pins at the lower left + +### SoC +[Hi35218EV300](https://www.hisilicon.com/en/products/smart-vision/consumer-camera/IOTVision/Hi3518EV300) +- ARM Cortex-A7@ 900 MHz +- 64Mb DDR2 + + + + +### Wifi +[RTL8188FTV](https://www.realtek.com/en/products/communications-network-ics/item/rtl8188ftv) +- 802.11b/g/n 2.4G +- USB interface + + + + +### SPI NOR flash +[XM25QH128A](https://www.xmcwh.com/en/site/product_con/200) +- 16Mb SPI NOR Flash + + + + +### UART pins (serial port) + + + + + +### GPIOs + +| nr | Description | +|-----|-------------| +| 0x0f (15) | irCut_1 | +| 0x0c (12) | irCut_2 | +| 0x28 (40) | IR Led | +| 0x33 (51) | Red Led | +| 0x32 (50) | Blue Led | +| 0x0d (13) | wlan power | +| 0x00 (0) | AcShdn | +| 0x09 (9) | Reset button | +| 0x3b (59) | Tilt motor A1 | +| 0x3a (58) | Tilt motor A2 | +| 0x39 (57) | Tilt motor B1 | +| 0x38 (56) | Tilt motor B2 | +| 0x47 (71) | Pan motor A1 | +| 0x45 (69) | Pan motor A2 | +| 0x46 (70) | Pan motor B1 | +| 0x44 (68) | Pan motor B2 | + +### Mods +#### USB Serial port + +There is a micro usb connector to power the camera and with some soldering this connector can be also be used for a serial to usb converter. +If you find it hard to solder the wires on the camera micro usb connector get a [micro usb breakout board](https://www.google.com/search?q=micro+usb+breakout+board&tbm=isch). + + + +1. Get a 3.3V TTL to USB converter (using a cheap pl2303hx one) +2. Remove the USB-A connector and pins +3. Connect the camera micro usb port to the converter +4. Connect the camera uart to the converter + + +## Original firmware + +The camera has a password protected uBoot. + +### [ipctool](https://github.com/OpenIPC/ipctool) output: +(soon...) + +#### cat /proc/mtd +``` +dev: size erasesize name +mtd0: 00060000 00010000 "bld" 393216 0 +mtd1: 00010000 00010000 "env" 65536 393216 +mtd2: 00010000 00010000 "enc" 65536 458752 +mtd3: 00010000 00010000 "sysflg" 65536 524288 +mtd4: 00380000 00010000 "sys" 3670016 589824 +mtd5: 00680000 00010000 "app" 6815744 4259840 +mtd6: 00180000 00010000 "cfg" 1572864 11075584 +mtd7: 00100000 00010000 "recove" 1048576 12648448 +mtd8: 002d0000 00010000 "user" 2949120 13697024 +mtd9: 00020000 00010000 "oeminfo" 131072 16646144 - 16777216 +``` + + +### dmesg +(soon...) + + +## OpenIPC firmware + +#### Boot dump +``` +Uncompress Ok! + +U-Boot 2016.11-g059901b-dirty (Oct 13 2021 - 20:14:30 +0300)hi3518ev300 + +Relocation Offset is: 0374a000 +Relocating to 43f4a000, new gd at 43f09ef0, sp at 43f09ed0 +SPI Nor: hifmc_ip_ver_check(44): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(50): Found +hifmc_spi_nor_probe(1709): SPI Nor ID Table Version 1.0 +hifmc_spi_nor_probe(1734): SPI Nor(cs 0) ID: 0x20 0x70 0x18 +hifmc_spi_nor_probe(1799): Block:64KB hifmc_spi_nor_probe(1800): Chip:16MB hifmc_spi_nor_probe(1801): Name:"XM25QH128A" +hifmc100_spi_nor_probe(147): SPI Nor total size: 16MB +NAND: 0 MiB +MMC: hisi-sdhci: 0 (SD) +In: serial +Out: serial +Err: serial +Net: eth0 +Warning: eth0 (eth0) using random MAC address - 6e:9f:f3:d7:33:35 + +Hit any key to stop autoboot: 0 +device 0 offset 0x50000, size 0x200000 + +SF: 2097152 bytes @ 0x50000 Read: OK +## Booting kernel from Legacy Image at 42000000 ... + Image Name: Linux-4.9.37-hi3518ev300 + Image Type: ARM Linux Kernel Image (uncompressed) + Data Size: 1891696 Bytes = 1.8 MiB + Load Address: 40008000 + Entry Point: 40008000 + Loading Kernel Image ... OK + +Starting kernel ... + +Booting Linux on physical CPU 0x0 +Linux version 4.9.37 (runner@fv-az241-255) (gcc version 7.5.0 (Buildroot -g29dde73) ) #1 Sun Jan 9 03:44:04 UTC 2022 +CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d +CPU: div instructions available: patching division code +CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache +OF: fdt:Machine model: Hisilicon HI3518EV300 DEMO Board +cmz zone is not set! +Memory policy: Data cache writeback +CPU: All CPU(s) started in SVC mode. +Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 +Kernel command line: mem=32M console=ttyAMA0,115200 panic=20 rootfstype=squashfs root=/dev/mtdblock3 init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel +),5120k(rootfs),-(rootfs_data) mmz_allocator=hisi +PID hash table entries: 128 (order: -3, 512 bytes) +Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) +Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) +Memory: 27104K/32768K available (3861K kernel code, 141K rwdata, 872K rodata, 188K init, 179K bss, 5664K reserved, 0K cma-reserved) +Virtual kernel memory layout: + vector : 0xffff0000 - 0xffff1000 ( 4 kB) + fixmap : 0xffc00000 - 0xfff00000 (3072 kB) + vmalloc : 0xc2800000 - 0xff800000 ( 976 MB) + lowmem : 0xc0000000 - 0xc2000000 ( 32 MB) + modules : 0xbf000000 - 0xc0000000 ( 16 MB) + .text : 0xc0008000 - 0xc03cd778 (3862 kB) + .init : 0xc04a9000 - 0xc04d8000 ( 188 kB) + .data : 0xc04d8000 - 0xc04fb520 ( 142 kB) + .bss : 0xc04fd000 - 0xc0529fe4 ( 180 kB) +SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 +NR_IRQS:16 nr_irqs:16 16 +Gic dist init... +arm_arch_timer: Architected cp15 timer(s) running at 50.00MHz (phys). +clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns +sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns +Switching to timer-based delay loop, resolution 20ns +clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns +Console: colour dummy device 80x30 +Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000) +pid_max: default: 32768 minimum: 301 +Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) +Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) +CPU: Testing write buffer coherency: ok +Setting up static identity map for 0x40008200 - 0x40008258 +devtmpfs: initialized +VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 +clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns +futex hash table entries: 256 (order: -1, 3072 bytes) +pinctrl core: initialized pinctrl subsystem +NET: Registered protocol family 16 +DMA: preallocated 256 KiB pool for atomic coherent allocations +Serial: AMBA PL011 UART driver +12040000.uart: ttyAMA0 at MMIO 0x12040000 (irq = 21, base_baud = 0) is a PL011 rev2 +console [ttyAMA0] enabled +12041000.uart: ttyAMA1 at MMIO 0x12041000 (irq = 22, base_baud = 0) is a PL011 rev2 +ssp-pl022 12070000.spi: ARM PL022 driver, device ID: 0x00800022 +ssp-pl022 12070000.spi: mapped registers from 0x12070000 to c286b000 +ssp-pl022 12071000.spi: ARM PL022 driver, device ID: 0x00800022 +ssp-pl022 12071000.spi: mapped registers from 0x12071000 to c286f000 +usbcore: registered new interface driver usbfs +usbcore: registered new interface driver hub +usbcore: registered new device driver usb +clocksource: Switched to clocksource arch_sys_counter +NET: Registered protocol family 2 +TCP established hash table entries: 1024 (order: 0, 4096 bytes) +TCP bind hash table entries: 1024 (order: 0, 4096 bytes) +TCP: Hash tables configured (established 1024 bind 1024) +UDP hash table entries: 256 (order: 0, 4096 bytes) +UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) +NET: Registered protocol family 1 +RPC: Registered named UNIX socket transport module. +RPC: Registered udp transport module. +RPC: Registered tcp transport module. +RPC: Registered tcp NFSv4.1 backchannel transport module. +workingset: timestamp_bits=30 max_order=13 bucket_order=0 +squashfs: version 4.0 (2009/01/31) Phillip Lougher +jffs2: version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) +io scheduler noop registered +io scheduler deadline registered (default) +pl061_gpio 120b0000.gpio_chip: PL061 GPIO chip @0x120b0000 registered +pl061_gpio 120b1000.gpio_chip: PL061 GPIO chip @0x120b1000 registered +pl061_gpio 120b2000.gpio_chip: PL061 GPIO chip @0x120b2000 registered +pl061_gpio 120b4000.gpio_chip: PL061 GPIO chip @0x120b4000 registered +pl061_gpio 120b5000.gpio_chip: PL061 GPIO chip @0x120b5000 registered +pl061_gpio 120b6000.gpio_chip: PL061 GPIO chip @0x120b6000 registered +pl061_gpio 120b7000.gpio_chip: PL061 GPIO chip @0x120b7000 registered +pl061_gpio 120b8000.gpio_chip: PL061 GPIO chip @0x120b8000 registered +brd: module loaded +loop: module loaded +hisi-sfc hisi_spi_nor.0: SPI Nor ID Table Version 1.2 +hisi-sfc hisi_spi_nor.0: The ID: 0x20 isn't in the BP table, Current device can't not protect +@spi_nor_scan(), no "m25p,fast-read". +@spi_nor_scan(), modes->rd_modes:0xd. +hisi-sfc hisi_spi_nor.0: (Fast) Read: opcode=BBh, protocol=122, mode=0, wait=8 +hisi-sfc hisi_spi_nor.0: nor->read_opcode[3: Read; 0B: Fast Read; 3B: Dual; BB: Dual IO; 6B: Quad; EB: Quad IO]: 0xbb. +hisi-sfc hisi_spi_nor.0: xm25qh128a (Chipsize 16 Mbytes, Blocksize 64KiB) +5 cmdlinepart partitions found on MTD device hi_sfc +5 cmdlinepart partitions found on MTD device hi_sfc +Creating 5 MTD partitions on "hi_sfc": +0x000000000000-0x000000040000 : "boot" +0x000000040000-0x000000050000 : "env" +0x000000050000-0x000000250000 : "kernel" +0x000000250000-0x000000750000 : "rootfs" +0x000000750000-0x000001000000 : "rootfs_data" +SPI Nand ID Table Version 2.7 +Cannot found a valid SPI Nand Device +hisi_spi_nand_probe(175): Error: driver probe, result: -19 +No OTP data, festa PHY use default ATE parameters! +festa PHY wait autotrim done timeout! +libphy: hisi_femac_mii_bus: probed +libphy: Fixed MDIO Bus: probed +hisi-femac 10040000.ethernet: connect to PHY failed! +xhci-hcd xhci-hcd.0.auto: xHCI Host Controller +xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 +xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6c hci version 0x110 quirks 0x20010010 +xhci-hcd xhci-hcd.0.auto: irq 116, io mem 0x10030000 +hub 1-0:1.0: USB hub found +hub 1-0:1.0: 1 port detected +xhci-hcd xhci-hcd.0.auto: xHCI Host Controller +xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 +usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. +hub 2-0:1.0: USB hub found +hub 2-0:1.0: hub can't support USB3.0 +hibvt_rtc 120e0000.rtc: rtc core: registered 120e0000.rtc as rtc0 +hibvt_rtc 120e0000.rtc: RTC driver for hibvt enabled +i2c /dev entries driver +hibvt-i2c 12060000.i2c: hibvt-i2c0@100000hz registered +hibvt-i2c 12061000.i2c: hibvt-i2c1@100000hz registered +hibvt-i2c 12062000.i2c: hibvt-i2c2@100000hz registered +sdhci: Secure Digital Host Controller Interface driver +sdhci: Copyright(c) Pierre Ossman +sdhci-pltfm: SDHCI platform and OF driver helper +mmc0: SDHCI controller on 10010000.sdhci [10010000.sdhci] using ADMA in legacy mode +mmc1: SDHCI controller on 10020000.sdhci [10020000.sdhci] using ADMA in legacy mode +NET: Registered protocol family 10 +NET: Registered protocol family 17 +hibvt_rtc 120e0000.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0) +VFS: Mounted root (squashfs filesystem) readonly on device 31:3. +devtmpfs: mounted +Freeing unused kernel memory: 188K (c04a9000 - c04d8000) +This architecture does not have kernel memory protection. +mmc0: new high speed SDHC card at address 1234 +mmcblk0: mmc0:1234 SA08G 7.21 GiB + mmcblk0: p1 +Starting syslogd: OK +Starting klogd: OK +Running sysctl: OK +Loading modules:Initializing random number generator: OK +Saving random seed: OK +Starting rngd: OK +Starting mdev... +F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock +F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock +F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock +F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock +Starting network: OK +Starting ntpd: OK +Starting dropbear sshd: OK +Starting httpd: OK +Starting mini-snmpd: DISABLED, OK +Starting telnetd: DISABLED, OK +Starting crond: OK +mmz_start: 0x42000000, mmz_size: 32M +hisilicon: Get data from environment and set SENSOR as jxf23 +insert audio +Bringing wlan0 up... +Successfully initialized wpa_supplicant +rfkill: Cannot open RFKILL control device +udhcpc: started, v1.31.1 +udhcpc: sending discover +udhcpc: sending discover +udhcpc: sending discover +udhcpc: sending select for 192.168.1.112 +udhcpc: lease of 192.168.1.112 obtained, lease time 86400 +deleting routers +adding dns 8.8.8.8 +adding dns 8.8.4.4 +hisilicon: Check MAC for Xiongmai devices +hisilicon: The eth0 interface has a correct MAC - +hisilicon: Loading of kernel modules and initialization of the video system has started +Starting majestic: OK + +Welcome to OpenIPC v2.1 +openipc-hi3518ev300 login: +``` + + +(soon...) + +### rtl8188fu +(soon...) + +### Motor driver +(soon...) + + + +## Flashing +(soon...)