diff --git a/README.md b/README.md
index f5f0a90..79868ad 100644
--- a/README.md
+++ b/README.md
@@ -59,6 +59,7 @@ OpenIPC Wiki
 - [An Orange Pi 5 minimal VRX for Goggles](en/fpv-orange-pi-5-groundstation.md)
 - [A selection of OpenIPC videos on YouTube](en/fpv-youtube.md)
 - [RunCam WiFiLink based on OpenIPC](en/fpv-runcam-wifilink-openipc.md)
+- [Radxa based groundstation](en/fpv-radxa.md)
 
 ### Troubleshooting
 
diff --git a/en/fpv-radxa.md b/en/fpv-radxa.md
new file mode 100644
index 0000000..6f3c944
--- /dev/null
+++ b/en/fpv-radxa.md
@@ -0,0 +1,62 @@
+# OpenIPC Wiki
+[Table of Content](../README.md)
+
+OpenIPC FPV ground station
+--------------------------
+
+<p align="center">
+  <img src="https://github.com/OpenIPC/wiki/blob/master/images/fpv-logo.jpg?raw=true" alt="Logo"/>
+</p>
+
+Here is a good [getting started](https://wiki.radxa.com/Zero/getting_started) if you are not familiar with Radza. 
+
+### Flashing 
+
+* SDCard
+[Link](https://github.com/OpenIPC/sbc-groundstations/releases) to latest
+
+* EMMC
+[How to flash the image to your onboard emmc](https://github.com/OpenIPC/sbc-groundstations/blob/master/radxa_pi_zero_3w/flashing_to_the_onboard_memory.md)
+
+
+### Wifi
+
+You can [setup the onboard wifi](https://github.com/OpenIPC/sbc-groundstations/blob/master/radxa_pi_zero_3w/headless_setup.md#setup-of-autoconnect-on-boot) for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)
+
+Note: for RubyFPV you will either need a USB Network Dongle like the one below
+
+ ![Picture](../images/fpv-radxa-usbc-lan.png)
+
+or access serial console, please check [here](https://wiki.radxa.com/Zero/dev/serial-console) on how to do that.
+
+### DVR with FPV firmware
+
+DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:
+
+
+![image](../images/fpv-radxa-gpio.png)
+
+To record DVR, push the button once. The stream will start and DVR will begin recording. When finished, push the button once to stop the recording and save the file.
+
+DVR is saved to the Videos folder in your home directory. DVR can be accessed either at /home/radxa/Videos or via a media server. Connect your groundstation to your home network and it can be accessed via a web browser at x.x.x.x:8080 -- replace x.x.x.x with your groundstation's local ip address.
+
+Connect Led long lead to +5v, Led short lead via a 1k resistor to GPIOAO_2 (The other BLUE pin on Radxa),
+
+```bash
+sudo gpioset gpiochip4 11=0      # turn LED on
+sudo gpioset gpiochip4 11=1      # turn LED off (actually it is very                             # simply lit because i guess logic level 0 is not 0 volts)
+```
+
+Circuit wiring:  +5v —>  +Led- —-> 1k resistor —> pin 28 on Radxa z3w (aka the other blue pin)
+
+<hr>
+
+A note about the DVR recording in this image. To ease the strain on the processor, we record to to a ts file rather than mp4 or mkv. As a result, there is no "smear" effect recorded, the uncaptured frames are simply dropped. You may notice jumps in your recording where there was no frame information.
+
+### Links to some helpful tools
+
+* [Windows Tools](https://dl.radxa.com/zero/tools/windows/)
+* [Other, All OS](https://dl.radxa.com/tools/)
+
+### RubyFPV
+see [RubyFPV Hardware](https://rubyfpv.com/hardware.php)
\ No newline at end of file
diff --git a/images/fpv-radxa-gpio.png b/images/fpv-radxa-gpio.png
new file mode 100644
index 0000000..3109c59
Binary files /dev/null and b/images/fpv-radxa-gpio.png differ
diff --git a/images/fpv-radxa-usbc-lan.png b/images/fpv-radxa-usbc-lan.png
new file mode 100644
index 0000000..e27c60f
Binary files /dev/null and b/images/fpv-radxa-usbc-lan.png differ